Articles | Volume 8, issue 3
https://doi.org/10.5194/wes-8-433-2023
https://doi.org/10.5194/wes-8-433-2023
Research article
 | 
29 Mar 2023
Research article |  | 29 Mar 2023

Validation of turbulence intensity as simulated by the Weather Research and Forecasting model off the US northeast coast

Sheng-Lun Tai, Larry K. Berg, Raghavendra Krishnamurthy, Rob Newsom, and Anthony Kirincich
Abstract

Turbulence intensity (TI) is often used to quantify the strength of turbulence in wind energy applications and serves as the basis of standards in wind turbine design. Thus, accurately characterizing the spatiotemporal variability in TI should lead to improved predictions of power production. Nevertheless, turbulence measurements over the ocean are far less prevalent than over land due to challenges in instrumental deployment, maintenance, and operation. Atmospheric models such as mesoscale (weather prediction) and large-eddy simulation (LES) models are commonly used in the wind energy industry to assess the spatial variability of a given site. However, the TI derivation from atmospheric models has not been well examined. An algorithm is proposed in this study to realize online calculation of TI in the Weather Research and Forecasting (WRF) model. Simulated TI is divided into two components depending on scale, including sub-grid (parameterized based on turbulence kinetic energy (TKE)) and grid resolved. The sensitivity of sea surface temperature (SST) on simulated TI is also tested. An assessment is performed by using observations collected during a field campaign conducted from February to June 2020 near the Woods Hole Oceanographic Institution Martha's Vineyard Coastal Observatory. Results show that while simulated TKE is generally smaller than the lidar-observed value, wind speed bias is usually small. Overall, this leads to a slight underestimation in sub-grid-scale estimated TI. Improved SST representation subsequently reduces model biases in atmospheric stability as well as wind speed and sub-grid TI near the hub height. Large TI events in conjunction with mesoscale weather systems observed during the studied period pose a challenge to accurately estimating TI from models. Due to notable uncertainty in accurately simulating those events, this suggests summing up sub-grid and resolved TI may not be an ideal solution. Efforts in further improving skills in simulating mesoscale flow and cloud systems are necessary as the next steps.

1 Introduction

While the number of wind turbines installed offshore in US waters is small, it is expected to continuously escalate for the foreseeable future (Musial et al., 2021). Therefore, it is critical to accurately simulate the wind resource, as well as the turbulence, in offshore environments. Wind power generation is sensitive to atmospheric turbulence in addition to wind speed (Yang et al., 2017; Berg et al., 2019; Vanderwende and Lundquist, 2012; St. Martin et al., 2016; Wharton and Lundquist, 2012). Atmospheric turbulence impacts the loads on the turbine and, ultimately, the life span of the wind turbine (Mücke et al., 2011). Even in the ambient environment without any turbulence, the turbine itself generates turbulence via its wake (Wu and Porté-Agel, 2012; Brand et al., 2011; Porté-Agel et al., 2020; Hansen et al., 2012).

Turbulence is generally largest near the surface where the wind shear and buoyancy are generally largest, and it is closely connected to stability in the planetary boundary layer (PBL) (Rodrigo et al., 2015; Bardal et al., 2018; Garratt, 1994). Compared to conditions over land, the sea surface is relatively smooth, leading to smaller amounts of shear-generated turbulence near the surface. In addition, while the continental PBL is generally unstable during the day, the diurnal variation in marine PBL is not evident but dependent on the thermal gradient between the sea surface and atmosphere above. Thus, the atmosphere is generally less turbulent offshore than onshore (e.g., Bodini et al., 2020). Nevertheless, strong turbulence-producing events such as hurricanes, winter storms, and mesoscale convective systems can impact offshore wind farms.

In wind energy applications, turbulence is often quantified using turbulence intensity (TI) (Bodini et al., 2020; Barthelmie et al., 2007), and TI is the basis of standards used in wind turbine design (e.g., Shaw et al., 1974). Accurately characterizing the spatiotemporal variability in TI should lead to improved predictions of power production. Earlier studies have discussed how TI may influence the power production of turbines (Bardal and Sætran, 2017; Kaiser et al., 2007; Saint-Drenan et al., 2020; Clifton and Wagner, 2014). It has been shown that power production during periods of high or low TI can vary by up to 20 % (Lundquist and Clifton, 2012). However, turbulence and stability measurements over the ocean are made far less frequently than over land as it is challenging to maintain and operate instruments over the open ocean for long durations.

Atmospheric models such as weather prediction and large-eddy simulation (LES) models can potentially bridge this gap as they can simulate turbulence based on atmospheric and surface conditions for any region over the globe. While LES models are too computationally expensive to simulate long periods of time, mesoscale meteorological models are much more efficient and can also estimate turbulent properties such as turbulence kinetic energy (TKE) by applying an applicable turbulence parameterization. Nevertheless, the derivation of TI from atmospheric models has rarely been examined. Since multiple model uncertainties may contribute to TI bias under various conditions, comprehensive observational datasets are desired for model validation and to help quantify the errors.

This study addresses these shortcomings to derive TI from a mesoscale weather model and access its performance in an offshore environment. We implement an online calculation of TI in the standard version of the Weather Research and Forecasting (WRF) model and complete a quantitative assessment of simulated TI using observations collected during a field campaign conducted from February to June 2020 near the Woods Hole Oceanographic Institution (WHOI) Martha's Vineyard Coastal Observatory (MVCO). Simulations incorporating high-resolution sea surface temperature (SST) are performed to evaluate the impact of SST on changing the atmospheric stability and simulated values of TI.

The paper is organized as follows: observational datasets used in this study are described in Sect. 2. Details of model configuration, TI derivations, and experimental design are provided in Sect. 3. Section 4 covers our primary findings including (a) wind and turbulence profiles near the sea surface, along with corresponding air–sea temperature difference; (b) the sensitivity of simulated wind and turbulence to SST forcing; (c) the relationship between TI and the bulk Richardson number; and (d) the role of model-resolved TI. To conclude, a summary and discussion are given in Sect. 5.

2 Observational data

A US Department of Energy (DOE)- and Bureau of Ocean Energy Management-supported field campaign was conducted from February through June 2020 near the Woods Hole Oceanographic Institution (WHOI) Martha's Vineyard Coastal Observatory (MVCO; Austin et al., 2000) with the goal of evaluating the performance of DOE's lidar buoys (Gorton and Shaw, 2020; Krishnamurthy et al., 2021; Sheridan et al., 2022). The MVCO is a purpose-built facility for conducting detailed atmospheric and oceanic research. A major component of the MVCO is the Air-Sea Interaction Tower (ASIT), built near the vicinity of the Rhode Island and Massachusetts wind energy areas (Fig. 1). At the site, a suite of wind energy specific measurements were made, including a pair of cup anemometers at the top of the tower (26 m a.m.s.l. – above mean sea level), a wind vane at 23 m a.m.s.l., and a WindCube v2 vertically profiling lidar (hereafter reference lidar) on the main platform located 13 m a.m.s.l. The centers of the reference lidar range gates are 53, 60, 80, 90, 100, 120, 140, 160, 180, and 200 m a.m.s.l. WindCube v2 measures line-of-sight radial velocity sequentially along four cardinal directions, with a zenith angle of 28, and a fifth beam is vertically pointed. The temporal resolution along each beam direction is 1.25 Hz. A carrier-to-noise ratio of −23 dB was used to filter the raw radial velocity measurements. Two DOE buoys equipped with a Doppler lidar (also a WindCube v2), surface met station, wave sensors, and current profilers were deployed within 200 m of the ASIT tower (hereafter buoy lidar). With predominant summer winds from ∼250 and winter winds from ∼320, the configuration of the buoy lidar and ASIT was designed to minimize wind wakes on the buoys from the tower. The reference heights of the buoy lidars matched the reference lidar heights. In addition, the air temperature at 4 m (using a Rotronic MP101A sensor) and sea surface temperature were collected using a YSI thermometer on the buoy lidar (41.33 N, 70.57 E and 41.32 N, 70.57 W) and are used to determine the buoyancy component of local stability. In this analysis, we use the reference lidar TI calculations for comparison to simulated TI, since the buoy induces additional motion which results in higher uncertainty in TI estimates (Gottschall et al., 2017; Kelberlau et al., 2020). Additional research is ongoing to improve TI calculations using buoy lidar measurements.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f01

Figure 1(a) Map depicting the WRF domain used in this study. Red star denotes the location of the MVCO ASIT. Color shading represents the terrain height in kilometers. (b) Schematics of WHOI's Air-Sea Interaction Tower (ASIT) including all pertinent elevations and dimensions of the tower structure and fixed metocean sensors. The reference lidar system is located outboard on the platform deck. MLW denotes mean low water.

TI is defined as the standard deviation of the horizontal wind speed (σU) divided by the average horizontal wind speed over a time interval (U):

(1) TI = σ U U , U = u 2 + v 2 .

Horizontal wind vectors (u and v) from the reference lidar were calculated at ∼1 Hz using the raw radial velocity measurements along the cardinal directions. Although the winds are reconstructed at 1 Hz, the winds are a combined product of a trailing ∼4 s of sampled radial velocity measurements. Any radial velocity measurement below a −23 dB signal-to-noise ratio threshold was filtered. The reconstructed 1 Hz horizontal wind speed measurements are used to calculate TI from the Doppler lidar as shown in Eq. (1) over 10 min. TKE is generally estimated as

(2) TKE = 1 2 σ u 2 + σ v 2 + σ w 2 ,

where σu2, σv2, and σw2 are the variances of zonal, meridional, and vertical wind components, respectively. For 10 min averaged TKE from reference lidar profilers, horizontal velocity variance was estimated using the 1 Hz u and v components of velocity, and the vertical velocity variance was estimated using the lidar central beam staring vertically up (like in Arthur et al., 2022). Only the measurements with greater than 90 % data availability over the 10 min averaging periods are used.

3 Model descriptions

3.1 Configuration

The model configuration, including horizontal and vertical grid spacing, spin-up time and selections of atmospheric, SST forcing, and PBL and surface layer parameterizations, can contribute to the uncertainty in simulated offshore wind (Bodini et al., 2021; Siedersleben et al., 2020; Hahmann et al., 2015; Chang et al., 2015; Sward et al., 2023; Optis et al., 2021). In this study, the version 4.2 WRF model is used to simulate offshore near-surface winds. A single model domain centered on the MVCO site is used that encompasses part of the northeastern USA and adjacent oceans (Fig. 1). The choices of model physics parameterizations for this study are consistent with the setup for the 20-year wind resource dataset released by the National Renewable Energy Laboratory (NREL) (Optis et al., 2020). Optis et al. (2020) conducted a series of model sensitivity experiments with respect to surface layer and PBL parameterizations, reanalysis data, and SST forcing. The results of their model assessment indicated that the largest uncertainty is associated with the choice of PBL parameterizations, and the Mellor–Yamada–Nakanishi–Niino (MYNN) boundary layer parameterization (Nakanishi and Niino, 2009) generally outperforms the Yonsei University (YSU; Hong et al., 2006) scheme off the east coast of North America. Hence the MYNN boundary layer parameterization, as well as other parameterizations described by Optis et al. (2020), was used for generating the CA20 dataset as well as our simulations. The model uses a horizontal grid spacing of 2 km and a stretched vertical coordinate with 60 levels. There are approximately 10 model levels between the surface and 200 m. The Eta (Ferrier) microphysics parameterization, MYNN surface layer parameterization, Unified Noah Land Surface Model parameterization (Chen and Dudhia, 2001), and RRTMG longwave and shortwave radiation parameterization (Iacono et al., 2008) are employed. Initial and boundary conditions are taken from NOAA's High-Resolution Rapid Refresh (HRRR; Benjamin et al., 2016) product. The HRRR analysis has several advantages over other coarse-resolution reanalysis products. For instance, (1) the model core of HRRR, the WRF model, is identical with what we use in this study; (2) it has a grid spacing of 3 km, which is very close to the grid spacing used here (2 km) to match the CA20 dataset; and (3) it is constrained hourly by assimilating radar observations including Doppler velocity and reflectivity, which reduces the uncertainties in the prediction of precipitating clouds. All these advantages would primarily mitigate model uncertainties in part due to issues in model balance and spin-up.

3.2 Diagnostics of turbulence intensity (TI)

Realistically, observed TI occurs across a range of spatial and temporal scales. Application of the WRF model leads to an artificial separation of motions that are explicitly represented by the model and turbulence treated by the boundary layer parameterization; thus both grid-resolved and sub-grid motions can give rise to TI. These two contributions to TI will be referred to as model-resolved and sub-grid TI, respectively. A new algorithm is implemented to extract the wind variation and mean wind speed over a 10 min window, allowing for the calculation of both sub-grid and model-resolved TI. Since the three-dimensional components of turbulent wind speed cannot be obtained through the boundary layer parameterization, the sub-grid TI is derived by leveraging TKE (Eq. 2) prognosed by the MYNN boundary layer parameterization.

The derivation of TI has been proposed in several studies including a recent document of Larsén (2022). In this report, the relation between TI and TKE is derived using the Kaimal boundary layer turbulence model (Kaimal and Finnigan, 1994). However, since the TI derivation in that work divides horizontal wind into along- and cross-turbine wind components rather than zonal and meridional winds that are used in WRF, we decided to apply the TI formula used in Shaw et al. (1974), Wharton and Lunquist (2011), and Bodini et al. (2020):

(3) TI = σ u 2 + σ v 2 U .

Our analysis using the lidar-measured wind variances collected at the MVCO ASIT over the study period indicates σw2 (variance of vertical wind) is generally much smaller than σu2 and σv2 (Fig. 2a) regardless of stability (Fig. 2b). In most of the conditions, the fraction of σw2 in total wind variance σw2σu2+σv2+σw2 is no greater than 0.2 (not shown). Moreover, it is found that the data points exceeding 0.2 mostly occur during neutral conditions, rather than during periods of unstable conditions, which we would normally expect.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f02

Figure 2The lidar-measured wind variances (σu2, σv2, and σw2) collected at the MVCO ASIT from January to mid-June in 2020. The data are displayed in the format of (a) power density and (b) the function of the air–sea temperature difference (atmospheric stability).

Download

Therefore, Eq. (3) can be approximated by the form of

(4) TI 2 TKE U .

The instantaneous sub-grid TI at any model time step can then be obtained by a scaling of the mean wind speed in a 10 min window following Eq. (4). A new variable was added to store the sub-grid TI and to have values written to the WRF model output files. In addition, the model was also modified to compute the model-resolved TI by adding calculations of running means and variances of the horizontal velocity components (zonal and meridional) within a 10 min window that are then used to compute and output the resolved TI. A summary of the two components of TI from the WRF model is given in Table 1.

Table 1Summary of comparison between two types of TI output from the WRF model.

Download Print Version | Download XLSX

3.3 Experimental design

To facilitate comparison against observations collected during the field campaign near the MVCO ASIT, the WRF model simulations were performed for February through June of 2020. The “baseline” experiment is a concatenation of a series of 36 h simulations. Each of these simulations is initialized at 00:00 UTC and continuously integrated for 36 h. To avoid model spin-up issues, the first 12 h of each individual simulation is discarded, and the resulting 24 h results are retained for the analysis.

Since the near-surface atmospheric stability can strongly influence turbulence intensity at hub height, the uncertainty in representation of sea surface temperature should also be considered. Despite the HRRR analysis representing convective-scale structures better than other coarse-resolution reanalysis products as mentioned earlier in Sect. 3.1, it does not provide corresponding SST forcing data. Therefore, a sensitivity experiment (named “sstupdate” hereafter) is conducted to examine the variability induced by replacing the SST forcing in the model.

Note that Optis et al. (2020) used two SST products including the Operational Sea Surface Temperature and Ice Analysis (OSTIA, resolution 0.05) dataset (Donlon et al., 2012) and the National Centers for Environmental Prediction (NCEP) Real-Time Global (RTG) SST product (Grumbine, 2020; resolution ∼0.083). Here, we use the NASA Jet Propulsion Laboratory (JPL) Level-4 MUR Global Foundation Sea Surface Temperature Analysis (V4.1, GHRSST; Chin et al., 2017), which has an even higher spatial resolution (0.01) than either OSTIA or NCEP RTG. The SST analysis product assimilates satellite data with a range of resolutions including the Moderate Resolution Imaging Spectroradiometer (MODIS) infrared (1 km), AVHRR infrared (5–9 km), microwave (25 km), and in situ measurements (pointwise). The multi-resolution variational analysis (MRVA) technique is employed to reconstruct fast-moving fine-scale features as well as to fill the large-scale data void. Note that since HRRR analysis data do not include SST, the baseline simulation uses the climatological SST provided with WRF as its forcing.

4 Results

4.1 Near-sea-surface wind, turbulence, and air–sea temperature gradient

The simulated wind speed (WSPD), wind direction (WDIR), TI, TKE, and air–sea temperature gradient (air temperature at 2 m above the surface (Tair) minus sea surface temperature (SST)) are compared against data measured by the tower-mounted lidar and buoy deployed at the ASIT site. We use the air–sea temperature gradient as a proxy for atmospheric stability near the sea surface. Negative values indicate unstable (convective) conditions, whereas stable conditions are likely when the temperature gradient is positive.

Here we highlight the comparisons by showing the results from March and May in 2020 as examples. The panels in Figs. 3 and 4 show a composite month-long comparison of near-surface properties between baseline simulations and the tower-mounted lidar for March and May, respectively. Note the model profiles in the figures only extend to 200 m to match the range of the lidar. The results show the model reproduces the major “convective” (negative values of Tair SST; red patches) events in March. While the simulated TKE is generally smaller than observed, both observations and simulations have larger TI and TKE during convective periods, indicating the model's PBL scheme reacts reasonably well in response to the varied lower boundary conditions. During stable periods (positive values of Tair SST; blue patches), simulated TKE and TI decrease dramatically with height. This indicates there is weak turbulence and limited vertical mixing in these cases. In addition, the seasonal variability in the air–sea temperature gradient is evident. For instance, the convective events in May were much shorter and weaker than those seen in March. This is most likely due to more frequent cold-air outbreaks in March than in late spring. The cold-air outbreaks are likely strongly convective periods due to the advection of cold air over relatively warm water. Cases with near-zero air–sea temperature gradients present a greater challenge as they have less tolerance in modeling inaccurate air–sea temperature differences and fluxes within the boundary layer.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f03

Figure 3Time–height comparison of wind speed (WSPD), wind direction (WDIR), air–sea temperature gradient (Tair SST), turbulence kinetic energy (TKE), and sub-grid turbulence intensity (TI). Results for lidar and buoy observations and baseline simulation during the period of March are given in (a) and (b), respectively.

Download

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f04

Figure 4Similar to Fig. 3, but results for May 2020 are displayed.

Download

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f05

Figure 5Scatterplots depicting the relationship between simulated (baseline) WSPD and sub-grid TI with color shadings for representing 80 m TI and TKE errors in (a) and (b), respectively.

Download

Table 2Metrics including correlation coefficient (CC), root mean square error (RMSE), and bias of 80 m TI, TKE, WSPD, and air–sea temperature difference are given as computed for baseline and sstupdate simulations.

Download Print Version | Download XLSX

To quantify the model performance for the entire period of study, an assessment of the baseline simulation is carried out that examines the 80 m TI, TKE, WSPD, and air–sea temperature gradients. Note data points from simulations and observations are only counted when wind speed is between 5 and 25 m s−1, which is consistent with turbine cut-in and cut-out wind speeds of commercial wind turbines. Three metrics including root mean square error (RMSE), bias, and the correlation coefficient (CC) are computed for each variable and given in Table 2. The root mean square error (RMSE) measures how close, on average, the simulated quantities are to observations.

(5) RMSE = 1 n i = 1 n y i - o i 2 1 2 ,

where y denotes the simulated result for the variable of interest, o represents the corresponding observation, and n is the number of data samples. The bias is also known as the mean prediction error (MPE). It compares the simulated against observed means of the evaluated dataset:

(6) bias = 1 n i = 1 n y i - o i .

The correlation coefficient (CC) is used to determine the similarity between the simulated and observed data. The CC value always lies between −1 and +1, representing the range from dissimilarity to a similar relation.

(7) CC = i = 1 n y i - y o i - o i = 1 n y i - y 2 i = 1 n o i - o 2 y = i = 1 n y i n , o = i = 1 n o i n

Overall, the WRF model slightly underestimates TI with a bias of −0.0061 (∼5 % relative to mean value) and has a RMSE of 0.037 (∼30 % relative to mean value). The two main factors in the computation of TI, TKE, and WSPD exhibit notable contrasts in their assessments. While simulated TKE is underpredicted with a bias of −0.3804 m2 s−2 and RMSE of 0.914 m2 s−2, WSPD generally agrees well with lidar observation as demonstrated by a relatively large correlation coefficient (0.83) in comparison to 0.74 for TKE. This implies that the errors in TI are likely driven by the differences in TKE as the WSPD is generally well predicted. We further examine how TI and TKE errors change correspondingly with WSPD as given in Fig. 5. The results confirm that, in most cases, large TI errors are associated with large TKE errors and have less dependency on WSPD. Lastly, the air–sea temperature gradient is reasonably represented with the highest correlation coefficient of 0.92 among all the variables.

4.2 Sensitivity of SST forcing on modeled wind and turbulence

As described in Sect. 3.3, the default SST in the baseline simulation is replaced by the NASA JPL SST analysis product (Chin et al., 2017), which has finer-scale features as opposed to the SST representation in the baseline simulation. This sensitivity experiment is named sstupdate, and the impacts of SST forcing are examined in this section.

The same metrics as those used in the previous section are applied to the sstupdate simulation and given in Table 2. These indicate the replacement of SST forcing has positive impacts on all the examined variables. For instance, the CC, RMSE, and bias for TI as simulated by sstupdate (baseline) are 0.59 (0.56), 0.035 (0.037), and −0.0023 (−0.0061). Similarly, the model skill improves simultaneously with respect to TKE, WSPD, and Tair SST. This implies more realistic SST forcing helps in better representing spatiotemporal evolution of stability and subsequently the surface fluxes. This then influences turbulent properties within the boundary layer such as the TKE and WSPD. A comparison of vertical profiles of TI RMSE between the two simulations (Fig. 6) further shows that SST representation in the model could affect skill in TI prediction from 60 to 190 m and that error generally increases with height. WSPD and TKE RMSE profiles present similar trends despite the range of improvement varying with height among the three variables. Redfern et al. (2023) show that the impact of SST replacement on wind speed modeling can be seen from 40 to 200 m. Their validation was done by comparing model results against lidar observations collected at three locations off Atlantic shores from June to July in 2022.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f06

Figure 6RMSE profiles of (a) TI, (b) WSPD, and (c) TKE for baseline (blue) and sstupdate (orange) simulations between 60 and 190 m.

Download

The probability density functions (PDFs) are given in Fig. 7 to help describe the similarities of each variable among the three datasets. Figure 7a shows that the distribution of observed TI has a wider peak between 0.025 and 0.1 than the simulated distributions. While the baseline simulation has more points with smaller TI values (peak around 0.04), the distributions of TI from the sstupdate show an additional peak around 0.09 and 0.1, and there are more large values of TI. The median TI of sstupdate (0.066) is much closer to observations (0.07) than the baseline (0.057), indicating that the SST representation has a notable impact on TI simulation. The individual impact of SST on the TKE, WSPD, and air–sea temperature difference is displayed in Fig. 7b–d, respectively. The model tends to produce more instances with small TKE than was observed (0.67; Fig. 7b), and sstupdate (0.4) has slightly larger median TKE than the baseline (0.377). Note part of the discrepancy in TKE may be attributed to varying uncertainty in lidar turbulence retrievals as a function of atmospheric stability. Sathe et al. (2015) found hub-height turbulence (∼80 m) measured by pulsed Doppler lidars could be significantly higher (lower) than what is observed by a sonic anemometer during unstable (stable) atmospheric conditions. The PDFs of WSPD in Fig. 7c indicate that while both simulations have relatively large medians (10.94 and 10.86) compared to the observations (10.31), the additional SST information used in sstupdate slightly improves the simulations. The overall improvement in WSPD may be attributed to more accurate representation of stability because the PDF of the simulated air–sea temperature gradient is improved when applying the improved SST forcing as shown by Fig. 7d.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f07

Figure 7Probability density function (PDF) plots illustrating the results of (a) sub-grid turbulence intensity (TI), (b) turbulence kinetic energy (TKE), (c) wind speed (WSPD), and (d) air–sea temperature difference among baseline, sstupdate simulations, and observations at hub height (∼80 m) from February to May of 2020. The color-coded median of each dataset is given in each panel.

Download

Application of the higher-resolution SST impacts the time of evolution of the winds and turbulence. Figure 8 shows how the cold bias seen in the SST of baseline simulation is effectively reduced during May 2020, which subsequently fixes the cold bias in near-surface air temperature. While there are relatively small differences between the two simulations in the TKE and WSPD, we do find improvement in TI over some periods. For example, during 5–8, 13–14, 17–18, and 30–31 May, TI simulated by the sstupdate simulation are generally higher than what is simulated by the baseline simulation and closer to the observed values. The correction of TKE has a larger impact on TI when WSPD is relatively small (less than 10 m s−1), which can be explained by how TI is calculated in Eq. (4).

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f08

Figure 8Time-series display of data from baseline, sstupdate simulations, and corresponding observations for May 2020. From top to bottom rows, the near-surface air temperature, sea surface temperature, hub-height TKE, WSPD, and TI are displayed.

Download

The impact of SST is also examined in the context of monthly variability. Figure 9 summarizes the metrics calculated for each simulation, variable, and month with the observational data as reference. The analysis suggests that the overall performance of the simulated air–sea temperature gradient (TG) is improved when the higher-resolution SST forcing is used, and the improvement is more prominent in the spring months than in February. Despite only slight impact on the correlation for the simulated TG by replacing the default SST (Fig. 9a), the corresponding RMSE (Fig. 9b) and bias (Fig. 9c) for the TG are considerably reduced. While a relatively small positive impact is shown for TKE and wind speed, the improvement in the bias of TI is prominent, as shown by the reduced RMSE and bias, particularly for April and May.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f09

Figure 9Metrics of the (a) correlation coefficient between the observations and simulations, (b) root mean square error (RMSE), and (c) bias for variables – TI, wind speed (WS), TKE, and air–sea temperature gradient (TG) – computed against the observations for each month between February and May in 2020. The dots with a solid line represent the baseline result. The triangles with a dashed line depict the corresponding values from the sstupdate simulation.

Download

4.3 Relationship between turbulence intensity and the bulk Richardson number

Many earlier studies showed that the bulk Richardson number (Rib) may be a good indicator of turbulent conditions as it considers stability associated with the temperature gradient, as well as the relative contributions of buoyancy and shear (e.g., Rodrigo et al., 2015; Bardal et al., 2018; Hsu, 1989; Zoumakis and Kelessis, 1991; Hansen et al., 2012). The equation we use for calculating the Rib is

(8) R i b = g Δ θ v Δ z θ v Δ U 2 + Δ V 2 ,

where g denotes gravitational acceleration, Δθv is the virtual potential temperature difference across a vertical layer of thickness Δz, and ΔU and ΔV represent the vertical gradient in horizontal wind components. The virtual potential temperature gradient (Δθv) is computed by using the air temperature (4 m) and sea surface temperature measurements on the buoy. The vertical gradients of the horizontal wind components (ΔU and ΔV) are obtained by using wind measurement at 100 m from the Doppler lidar (DL) and 4 m from the buoy. We also applied a similar approach using the WRF model output. Note the wind and temperature gradients are not computed from the same heights, and the bulk Richardson number calculated here will only be used to inform stability qualitatively (Howland et al., 2020). Data for cases where the wind speed was less than 5 m s−1 and greater than 25 m s−1 have been removed as described earlier. Figure 10a displays the calculated Rib in time series during February 2020 as an example. It shows that both experiments reproduce the occurrence of observed events with unstable conditions (large negative Rib values). For instance, on 14–15 and 19–21 February, the model was able to produce large TI (over 0.2, Fig. 10d) when the Rib approaches −10 (Fig. 10a).

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f10

Figure 10Time-series plots of observed and simulated (a) bulk Richardson number, (b) shear component (m2 s−2), (c) buoyancy component (K), and (d) sub-grid turbulence intensity (TI) during February 2020. Green arrows in (d) indicate events with large contrast in TI between the model and observation. Filtered data points of sub-grid TI by using the thresholds of buoyancy > 0 K, shear < 20.0 m2 s−2, and TI > 0.06 are denoted in (e). The green line represents the model-resolved TI.

Download

While simulated results show that the model has good skill for large-TI (over 0.2) events, there are periods with moderate TI (0.05 to 0.2) where the model misses the observed peaks as indicated by the green arrows in Fig. 10d. It is found that in those time periods, the buoyancy component (Δθv) is mostly near zero (neutral conditions) or even positive (stable), whereas the shear component (ΔU2V2) could be more variable over time, indicating that the model may have less skill in TI prediction when the buoyant forcing is weak.

To explore how TI can be related to the buoyancy and shear components of the Rib, TI is mapped in regard to the two terms (Fig. 11). Figure 11a shows that the observed TI is generally larger during periods when conditions are unstable and that there is a large magnitude of the negative buoyancy component (SST is larger than air temperature). This implies that in convective regimes (buoyancy component < 0), more vigorous turbulence leads to stronger vertical mixing, which significantly reduces the wind shear. On the other hand, in stable regimes (buoyancy component > 0), less turbulent mixing often results in larger values of wind shear.

https://wes.copernicus.org/articles/8/433/2023/wes-8-433-2023-f11

Figure 11Scatterplots mapping the hub-height sub-grid TI in the coordinates of buoyancy (Δθv) and shear (ΔU2V2) components for the entire period of study. Results of the (a) observation (OBS), (b) baseline simulation, (c) sstupdate simulation, and (d) percentage of fractional difference (%) between sstupdate and baseline simulations are displayed. The box marked with a dashed black line in (a) indicates the regime that is used to extract the data points as shown in Fig. 10e.

Download

Although in general, TI decreases as the buoyancy becomes more positive and the atmosphere becomes stable as identified in the observations and the two WRF model configurations (Fig. 11a–c), a population of reddish circles (large values of TI) in the lower-right quadrant of the figure does not follow this relationship (Fig. 11a). While both simulations fail to represent these cases (Fig. 11b and c), the fractional difference in simulated TI between the two simulations indicates that the sstupdate simulation generally has larger TI than the baseline simulation (Fig. 11d). This can be attributed to an overall reduction in the cold bias in the baseline simulation as shown in Fig. 9. Furthermore, a larger fractional increase in TI is found in the regime where the conditions are between neutral and slightly stable (buoyancy component  0). This is most likely due to the weak negative temperature gradient in the baseline simulation becoming positive after replacing the SST forcing. Despite the correction, large TI is rarely simulated in the lower-right regime. This result is not surprising as the formulation in the MYNN parameterization does not allow large values of TKE to be diagnosed in stable conditions.

The next step was to locate these specific data points in time by applying thresholds of buoyancy component > 0 K, shear component < 20.0 m2 s−2, and TI > 0.06 (Fig. 11a). It is shown that features leading to the large values of TI in the observation and simulations may not overlap in time as the model may fail to simulate realistic conditions (Fig. 10e). Nevertheless, it is found that many of these cases with a positive buoyancy component and large TI are aligned with periods that have notable differences between observed and simulated TI, as denoted by green arrows in Fig. 10d. Therefore, we conclude that the underrepresentation of this regime is likely responsible for the majority of the model bias in TI.

While some of the intermittent turbulent events may cause the occurrence of large TI under small shear and stable conditions, we find that most of the cases with high levels of TI in stable conditions and weak shear can be linked to fluctuations in wind speed associated with mesoscale features of the flow, and they are partially resolved by the mesoscale model, or for which there are timing errors. In Fig. 10e, the mesoscale (model-resolved) TI, described in Sect. 3.2, is denoted by the green line. For the periods such as 3–4, 6–7, and 10–11 February, when the simulated sub-grid TI is much smaller than that of observations, spikes in mesoscale (model-resolved) TI have amplitudes similar to the observed values. This suggests the need to consider both sub-grid and mesoscale TI when modeling TI derived from a mesoscale atmospheric model. Furthermore, the uncertainties in the timing of simulated mesoscale weather events may lead to notable contrasts between the timing of modeled and observed peaks in TI. This can impact the simulated TI in two ways as the mesoscale activity not only generates variance in the winds over larger spatiotemporal scales than the sub-grid turbulence does, but also effectively offsets dynamic and thermodynamic conditions near the sea surface in the boundary layer that influence the simulated sub-grid TI generated by the boundary layer parameterization. Our analysis demonstrates the utility of identifying scale-dependent uncertainties in TI modeling, which allows us to isolate the causes of errors in the simulated TI.

The metrics used in Table 1 are employed again to assess the impact of resolved TI on the TI prediction and are listed in Table 3. Results indicate that the addition of resolved TI reduces the bias for baseline configuration (−0.0061 to 0.0017) but enlarges the bias in the sstupdate configuration (−0.0023 to 0.0055). Moreover, there is worse correlation and RMSE when both sub-grid and resolved TI are considered. For instance, the correlation coefficients are reduced from 0.56 to 0.53 and 0.59 to 0.56 for baseline and sstupdate configurations, respectively. The effects of the higher-resolution SST forcing and resolved TI can lead to an overestimate of the TI, as the bias changes sign and the RMSE increases slightly compared to the sub-grid TI only. We suspect that this could be associated with the uncertainties in simulating mesoscale events as depicted in Fig. 10e. The events with larger resolved TI are not necessarily coincident with observations, which explains why simply summing up sub-grid and resolved TI in time may introduce additional errors into the simulated TI.

Table 3Metrics including the correlation coefficient (CC), root mean square error (RMSE), and bias for TI that are computed based on total (sub-grid and resolved) TI simulated by baseline and sstupdate simulations.

Download Print Version | Download XLSX

5 Summary and conclusion

Algorithms to derive TI are successfully implemented in the WRF model and tested offshore using a multi-month dataset collected at the MVCO using a combination of Doppler lidar, tower, and buoy data. Simulated TI is divided into two components depending on scale, comprising sub-grid and grid resolved. To obtain simulated TI, we calculate the square root of the sum of horizontal wind variances and then divide this by the mean wind speed over a 10 min window. While sub-grid TI is diagnosed from parameterized turbulence kinetic energy (TKE) through the MYNN PBL parameterization, resolved TI is estimated by using the model-resolved wind variances.

The modeled TI computed over a wide range of atmospheric conditions is analyzed and validated by using a variety of observations collected at the offshore tower at the MVCO between February and May in 2020. The primary findings include the following:

  • The model's PBL scheme reacts reasonably well to changes in the vertical temperature gradient near the sea surface despite the fact that the simulated TKE is generally smaller than what is observed by the lidar, especially for events with large TKE values.

  • The modified WRF model slightly underestimates TI, and the error is mainly attributed to relatively large negative bias in TKE as the predicted wind speed generally agrees with observation.

  • The WRF model has difficulty predicting periods of weak TI due to smaller air–sea temperature differences and fluxes within the simulated boundary layer.

  • Overall cold bias in the SST of baseline simulation is effectively reduced by substituting it with more accurate SST forcing. This subsequently reduces model biases in near-surface air temperature as well as in hub-height WSPD and TI.

  • A regime of large observed values of TI during periods with positive buoyancy and weak shear is identified, but the values are not captured by the model. Many of the events occurred in conjunction with mesoscale weather systems, but directly summing up sub-grid and resolved TI does not improve the TI prediction. This is because the primary source of uncertainty in those events is caused by the unrealistic representation of mesoscale weather systems, including timing errors, in the model.

Our analysis suggests additional model constraints are required to further improve model representation of TI and TKE in mesoscale or finer-scale cloud (system) processes. Approaches that couple mesoscale model with data assimilation techniques to improve skill in the simulated mesoscale flow features and cloud predictions (Tai et al., 2020, 2021; Gaudet et al., 2022) could be very beneficial.

Code availability

The codes implemented in the WRF model for the presented simulations as well as the scripts for data analysis can be made available upon request. In the case of interest, please contact the authors.

Data availability

The observational and simulated datasets used in this study can be made available upon request.

Author contributions

SLT: conceptualization, methodology, execution, analysis, and writing. LKB: conceptualization, methodology, supervision, and review. RK: observational data processing, consulting, and review. RN: observational data processing. AK: observational data consulting and review.

Competing interests

The contact author has declared that none of the authors has any competing interests.

Disclaimer

Publisher's note: Copernicus Publications remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Acknowledgements

Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy under contract DE-AC05-76RLO1830.

Financial support

This research was supported by the National Offshore Wind Research and Development Consortium under agreement number 147502.

Review statement

This paper was edited by Sukanta Basu and reviewed by three anonymous referees.

References

Arthur, R. S., Juliano, T. W., Adler, B., Krishnamurthy, R., Lundquist, J. K., Kosović, B., and Jiménez, P. A.: Improved Representation of Horizontal Variability and Turbulence in Mesoscale Simulations of an Extended Cold-Air Pool Event, J. Appl. Meteorol. Clim., 61, 685–707, https://doi.org/10.1175/JAMC-D-21-0138.1, 2022. 

Austin T. C., Edson, J. B., McGillis, W. R., von Alt, C., Purcell, M. J., Petitt, R., McElroy, M. K., Ware, J., and Stokey, R.: The Martha's Vineyard Coastal Observatory: A long term facility for monitoring air-sea processes, in: Proc. MTS/IEEE OCEANS, https://ieeexplore.ieee.org/abstract/document/882223 (last access: 28 March 2023), 1937–1941, 2000. 

Bardal, L. M. and Sætran, L. R.: Influence of turbulence intensity on wind turbine power curves, Energ. Proced., 137, 553–558, https://doi.org/10.1016/j.egypro.2017.10.384, 2017. 

Bardal, L. M., Onstad, A. E., Sætran, L. R., and Lund, J. A.: Evaluation of methods for estimating atmospheric stability at two coastal sites, Wind Eng., 42, 561–575, https://doi.org/10.1177/0309524X18780378, 2018. 

Barthelmie, R. J., Frandsen, S. T., Nielsen, M. N., Pryor, S. C., Rethore, P.-E., and Jørgensen, H. E.: Modelling and measurements of power losses and turbulence intensity in wind turbine wakes at Middelgrunden offshore wind farm, Wind Energy, 10, 517–528, https://doi.org/10.1002/we.238, 2007. 

Benjamin, S. G., Weygandt, S. S., Brown, J. M., Hu, M., Alexander, C. R., Smirnova, T. G., Olson, J. B., James, E. P., Dowell, D. C., Grell, G. A., Lin, H., Peckham, S. E., Smith, T. L., Moninger, W. R., Kenyon, J. S., and Manikin, G. S.: A North American Hourly Assimilation and Model Forecast Cycle: The Rapid Refresh, Mon. Weather Rev., 144, 1669–1694, https://doi.org/10.1175/MWR-D-15-0242.1, 2016. 

Berg, L. K., Liu, Y., Yang, B., Qian, Y., Olson, J., Pekour, M., Ma, P.-L., and Hou, Z.: Sensitivity of Turbine-Height Wind Speeds to Parameters in the Planetary Boundary-Layer Parametrization Used in the Weather Research and Forecasting Model: Extension to Wintertime Conditions, Bound.-Lay. Meteorol., 170, 507–518, https://doi.org/10.1007/s10546-018-0406-y, 2019. 

Bodini, N., Lundquist, J. K., and Kirincich, A.: Offshore Wind Turbines Will Encounter Very Low Atmospheric Turbulence, J. Phys.: Conf. Ser., 1452, 012023, https://doi.org/10.1088/1742-6596/1452/1/012023, 2020. 

Bodini, N., Hu, W., Optis, M., Cervone, G., and Alessandrini, S.: Assessing boundary condition and parametric uncertainty in numerical-weather-prediction-modeled, long-term offshore wind speed through machine learning and analog ensemble, Wind Energy Sci., 6, 1363–1377, https://doi.org/10.5194/wes-6-1363-2021, 2021. 

Brand, A. J., Peinke, J., and Mann, J.: Turbulence and wind turbines, J. Phys.: Conf. Ser., 318, 072005, https://doi.org/10.1088/1742-6596/318/7/072005, 2011. 

Chang, R., Zhu, R., Badger, M., Hasager, C. B., Xing, X., and Jiang, Y.: Offshore Wind Resources Assessment from Multiple Satellite Data and WRF Modeling over South China Sea, Remote Sens., 7, 467–487, https://doi.org/10.3390/rs70100467, 2015. 

Chen, F. and Dudhia, J.: Coupling an Advanced Land Surface–Hydrology Model with the Penn State–NCAR MM5 Modeling System. Part I: Model Implementation and Sensitivity, Mon. Weather Rev., 129, 569–585, https://doi.org/10.1175/1520-0493(2001)129<0569:CAALSH>2.0.CO;2, 2001. 

Chin, T. M., Vazquez-Cuervo, J., and Armstrong, E. M.: A multi-scale high-resolution analysis of global sea surface temperature, Remote Sens. Environ., 200, 154–169, https://doi.org/10.1016/j.rse.2017.07.029, 2017. 

Clifton, A. and Wagner, R.: Accounting for the effect of turbulence on wind turbine power curves, J. Phys.: Conf. Ser., 524, 012109, https://doi.org/10.1088/1742-6596/524/1/012109, 2014. 

Donlon, C. J., Martin, M., Stark, J., Roberts-Jones, J., Fiedler, E., and Wimmer, W.: The Operational Sea Surface Temperature and Sea Ice Analysis (OSTIA) system, Remote Sens. Environ., 116, 140–158, https://doi.org/10.1016/j.rse.2010.10.017, 2012. 

Garratt, J.: Review: the atmospheric boundary layer, Earth-Sci. Rev., 37, 89–134, https://doi.org/10.1016/0012-8252(94)90026-4, 1994. 

Gaudet, B. J., Medina, G. G., Krishnamurthy, R., Shaw, W. J., Sheridan, L. M., Yang, Z., Newsom, R. K., and Pekour, M.: Evaluation of Coupled Wind–Wave Model Simulations of Offshore Winds in the Mid-Atlantic Bight Using Lidar-Equipped Buoys, Mon. Weather Rev., 150, 1377–1395, https://doi.org/10.1175/MWR-D-21-0166.1, 2022. 

Gorton, A. M. and Shaw, W. J.: Advancing Offshore Wind Resource Characterization Using Buoy-Based Observations, Mar. Technol. Soc. J., 54, 37–43, https://doi.org/10.4031/MTSJ.54.6.5, 2020. 

Gottschall, J., Gribben, B., Stein, D., and Würth, I.: Floating lidar as an advanced offshore wind speed measurement technique: current technology status and gap analysis in regard to full maturity, WIREs Energ. Environ., 6, e250, https://doi.org/10.1002/wene.250, 2017. 

Grumbine, R.: Description of NCEP High Res, SST Analysis, https://polar.ncep.noaa.gov/sst/ophi/description.shtml (last access: 15 March 2023), 2020. 

Hahmann, A. N., Vincent, C. L., Peña, A., Lange, J., and Hasager, C. B.: Wind climate estimation using WRF model output: method and model sensitivities over the sea, Int. J. Climatol., 35, 3422–3439, https://doi.org/10.1002/joc.4217, 2015. 

Hansen, K. S., Barthelmie, R. J., Jensen, L. E., and Sommer, A.: The impact of turbulence intensity and atmospheric stability on power deficits due to wind turbine wakes at Horns Rev wind farm, Wind Energy, 15, 183–196, https://doi.org/10.1002/we.512, 2012. 

Hong, S.-Y., Noh, Y., and Dudhia, J.: A new vertical diffusion package with an explicit treatment of entrainment processes, Mon. Weather Rev., 134, 2318–2341, https://doi.org/10.1175/MWR3199.1, 2006. 

Howland, M. F., González, C. M., Martínez, J. J. P., Quesada, J. B., Larrañaga, F. P., Yadav, N. K., Chawla, J. S., and Dabiri, J. O.: Influence of atmospheric conditions on the power production of utility-scale wind turbines in yaw misalignment, J. Renew. Sustain. Energ., 12, 063307, https://doi.org/10.1063/5.0023746, 2020. 

Hsu, S. A.: The relationship between the Monin-Obukhov stability parameter and the bulk Richardson number at sea, J. Geophys. Res.-Oceans, 94, 8053–8054, https://doi.org/10.1029/JC094iC06p08053, 1989. 

Iacono, M. J., Delamere, J. S., Mlawer, E. J., Shephard, M. W., Clough, S. A., and Collins, W. D.: Radiative forcing by long-lived greenhouse gases: Calculations with the AER radiative transfer models, J. Geophys. Res.-Atmos., 113, D13103, https://doi.org/10.1029/2008JD009944, 2008. 

Kaimal, J. C. and Finnigan, J. J.: Title Pages, in: Atmospheric Boundary Layer Flows: Their Structure and Measurement, edited by: Kaimal, J. C. and Finnigan, J. J., Oxford University Press, https://doi.org/10.1093/oso/9780195062397.001.0001, 1994. 

Kaiser, K., Langreder, W., Hohlen, H., and Højstrup, J.: Turbulence Correction for Power Curves, in: Wind Energy, Springer, Berlin, Heidelberg, 159–162, https://doi.org/10.1007/978-3-540-33866-6_28, 2007. 

Kelberlau, F., Neshaug, V., Lønseth, L., Bracchi, T., and Mann, J.: Taking the Motion out of Floating Lidar: Turbulence Intensity Estimates with a Continuous-Wave Wind Lidar, Remote Sens., 12, 898, https://doi.org/10.3390/rs12050898, 2020. 

Krishnamurthy, R., Garcia-Medina, G., Gaudet, B., Mahon, A., Newsom, R., Shaw, W., and Sheridan, L.: Potential of Offshore Wind Energy off the Coast of California, in: OCEANS 2021: San Diego – Porto, 20–23 September 2021, San Diego, CA, USA, 1–6, https://doi.org/10.23919/OCEANS44145.2021.9705976, 2021. 

Larsén, X. G.: Calculating Turbulence Intensity from mesoscale modeled Turbulence Kinetic Energy, https://orbit.dtu.dk/en/publications/calculating-turbulence-intensity-from-mesoscale-modeled (last access: 3 January 2023), 2022. 

Lundquist, J. and Clifton, A.: How turbulence can impact power performance, https://www.wind-watch.org/documents/how-turbulence-can-impact-power-performance/ (last access: 15 March 2023), 2012. 

Mücke, T., Kleinhans, D., and Peinke, J.: Atmospheric turbulence and its influence on the alternating loads on wind turbines, Wind Energy, 14, 301–316, https://doi.org/10.1002/we.422, 2011. 

Musial, W., Spitsen, P., Beiter, P., Duffy, P., Marquis, M., Cooperman, A., Hammond, R., and Shields, M.: Offshore Wind Market Report: 2021 Edition, https://www.energy.gov/sites/default/files/2021-08/Offshore Wind Market Report 2021 Edition_Final.pdf (last access: 27 December 2022), 2021. 

Nakanishi, M. and Niino, H.: Development of an Improved Turbulence Closure Model for the Atmospheric Boundary Layer, J. Meteorol. Soc. Jpn. Ser. II, 87, 895–912, https://doi.org/10.2151/jmsj.87.895, 2009. 

Optis, M., Rybchuk, O., Bodini, N., Rossol, M., and Musial, W.: Offshore Wind Resource Assessment for the California Pacific Outer Continental Shelf, NREL – National Renewable Energy Laboratory, https://doi.org/10.2172/1677466, 2020. 

Optis, M., Kumler, A., Brodie, J., and Miles, T.: Quantifying sensitivity in numerical weather prediction-modeled offshore wind speeds through an ensemble modeling approach, Wind Energy, 24, 957–973, https://doi.org/10.1002/we.2611, 2021. 

Porté-Agel, F., Bastankhah, M., and Shamsoddin, S.: Wind-Turbine and Wind-Farm Flows: A Review, Bound.-Lay. Meteorol., 174, 1–59, https://doi.org/10.1007/s10546-019-00473-0, 2020. 

Redfern, S., Optis, M., Xia, G., and Draxl, C.: Offshore wind energy forecasting sensitivity to sea surface temperature input in the Mid-Atlantic, Wind Energ. Sci., 8, 1–23, https://doi.org/10.5194/wes-8-1-2023, 2023. 

Rodrigo, J. S., Cantero, E., García, B., Borbón, F., Irigoyen, U., Lozano, S., Fernande, P. M., and Chávez, R. A.: Atmospheric stability assessment for the characterization of offshore wind conditions, J. Phys.: Conf. Ser., 625, 012044, https://doi.org/10.1088/1742-6596/625/1/012044, 2015. 

Saint-Drenan, Y.-M., Besseau, R., Jansen, M., Staffell, I., Troccoli, A., Dubus, L., Schmidt, J., Gruber, K., Simões, S. G., and Heier, S.: A parametric model for wind turbine power curves incorporating environmental conditions, Renew. Energy, 157, 754–768, https://doi.org/10.1016/j.renene.2020.04.123, 2020. 

Sathe, A., Banta, R., Pauscher, L., Vogstad, K., Schlipf, D., and Wylie, S.: Estimating Turbulence Statistics and Parameters from Ground- and Nacelle-Based Lidar Measurements, IEA Wind Task 32 Expert Report, ISBN 978-87-93278-35-6, 2015. 

Shaw, R. H., Den Hartog, G., King, K. M., and Thurtell, G. W.: Measurements of mean wind flow and three-dimensional turbulence intensity within a mature corn canopy, Agric. Meteorol., 13, 419–425, https://doi.org/10.1016/0002-1571(74)90082-X, 1974. 

Sheridan, L. M., Krishnamurthy, R., García Medina, G., Gaudet, B. J., Gustafson Jr., W. I., Mahon, A. M., Shaw, W. J., Newsom, R. K., Pekour, M., and Yang, Z.: Offshore reanalysis wind speed assessment across the wind turbine rotor layer off the United States Pacific coast, Wind Energ. Sci., 7, 2059–2084, https://doi.org/10.5194/wes-7-2059-2022, 2022.  

Siedersleben, S. K., Platis, A., Lundquist, J. K., Djath, B., Lampert, A., Bärfuss, K., Cañadillas, B., Schulz-Stellenfleth, J., Bange, J., Neumann, T., and Emeis, S.: Turbulent kinetic energy over large offshore wind farms observed and simulated by the mesoscale model WRF (3.8.1), Geosci. Model Dev., 13, 249–268, https://doi.org/10.5194/gmd-13-249-2020, 2020. 

St. Martin, C. M., Lundquist, J. K., Clifton, A., Poulos, G. S., and Schreck, S. J.: Wind turbine power production and annual energy production depend on atmospheric stability and turbulence, Wind Energy Sci., 1, 221–236, https://doi.org/10.5194/wes-1-221-2016, 2016. 

Sward, J. A., Ault, T. R., and Zhang, K. M.: Spatial biases revealed by LiDAR in a multiphysics WRF ensemble designed for offshore wind, Energy, 262, 125346, https://doi.org/10.1016/j.energy.2022.125346, 2023. 

Tai, S.-L., Fast, J. D., Gustafson, W. I., Chand, D., Gaudet, B., Feng, Z., and Newsom, R.: Simulation of Continental Shallow Cumulus Populations Using an Observation-Constrained Cloud-System Resolving Model, J. Adv. Model. Earth Syst., 12, e2020MS002091, https://doi.org/10.1029/2020MS002091, 2020. 

Tai, S.-L., Feng, Z., Ma, P.-L., Schumacher, C., and Fast, J. D.: Representations of Precipitation Diurnal Cycle in the Amazon as Simulated by Observationally Constrained Cloud-System Resolving and Global Climate Models, J. Adv. Model. Earth Syst., 13, e2021MS002586, https://doi.org/10.1029/2021MS002586, 2021. 

Vanderwende, B. J. and Lundquist, J. K.: The modification of wind turbine performance by statistically distinct atmospheric regimes, Environ. Res. Lett., 7, 034035, https://doi.org/10.1088/1748-9326/7/3/034035, 2012. 

Wharton, S. and Lundquist, J. K.: Atmospheric stability affects wind turbine power collection, Environ. Res. Lett., 7, 014005, https://doi.org/10.1088/1748-9326/7/1/014005, 2012. 

Wu, Y.-T. and Porté-Agel, F.: Atmospheric Turbulence Effects on Wind-Turbine Wakes: An LES Study, Energies, 5, 5340–5362, https://doi.org/10.3390/en5125340, 2012. 

Yang, B., Qian, Y., Berg, L. K., Ma, P.-L., Wharton, S., Bulaevskaya, V., Yan, H., Hou, Z., and Shaw, W. J.: Sensitivity of Turbine-Height Wind Speeds to Parameters in Planetary Boundary-Layer and Surface-Layer Schemes in the Weather Research and Forecasting Model, Bound.-Lay. Meteorol., 162, 117–142, https://doi.org/10.1007/s10546-016-0185-2, 2017. 

Zoumakis, N. M. and Kelessis, A. G.: The dependence of the bulk Richardson number on stability in the surface layer, Bound.-Lay. Meteorol., 57, 407–414, https://doi.org/10.1007/BF00120057, 1991. 

Download
Short summary
Turbulence intensity is critical for wind turbine design and operation as it affects wind power generation efficiency. Turbulence measurements in the marine environment are limited. We use a model to derive turbulence intensity and test how sea surface temperature data may impact the simulated turbulence intensity and atmospheric stability. The model slightly underestimates turbulence, and improved sea surface temperature data reduce the bias. Error with unrealistic mesoscale flow is identified.
Altmetrics
Final-revised paper
Preprint